American Audio | V | User manual | American Audio V User manual American Audio® – – V Vplus Series Amplifiers Power. American audio V PLUS Pdf User Manuals. View online or download American audio V PLUS User Instructions. View and Download American Audio V/V user instructions online. PROFESSIONAL POWER AMPLIFIERS. V/V Amplifier pdf manual.

Author: Mikataur Aragul
Country: Tanzania
Language: English (Spanish)
Genre: Literature
Published (Last): 28 June 2015
Pages: 35
PDF File Size: 1.36 Mb
ePub File Size: 20.83 Mb
ISBN: 737-8-66905-313-8
Downloads: 79128
Price: Free* [*Free Regsitration Required]
Uploader: Goktilar

Carefully check the shipping carton for americna that may have occurred during shipping. When constructing your own XLR cables follow the pin configuration describe below for proper connections.

Turn your amp on. Ground Lift Switch – This switch is used to disconnect the internal ground signal from the amplifier chassis ground.

During audoo operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible. Check the line from the output terminal of the amplifier to amrican speaker.

Table of Contents Add to my manuals Add. Turn channel two gain up. The front panel provides four holes used to screw the unit into a rack. See page 9 for more details on input configuration. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector.


Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable. Clipping should be kept to a reasonable minimum. Gain Controls – The gain controls are located on the front panel and are calibrated in 2dB of attenuation from full gain. For cable runs shorter than 20ft. Auddio channel two positive output terminal for the negative connection and the channel one positive output terminal for the positive connection.

TOP Related  REXROTH DKCXX.3-040-7 PDF

American Audio V3000 PLUS Manuals

American audio professional power amplifer user instruction v 16 pages. When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction.

Apply an input source signal to your amplifier. If the carton appears to be damaged, carefully inspect your unit for any damage and be sure all accessories necessary to operate the system have arrived intact. A limiter takes the gain of an overloading signal and reduces it, the reduction in gain reduces distortion that can cause damage to your speakers and amplifier.

Please do not return the amplifier to your dealer without contacting customer support. No hay piezas adentro que el usario puede reparar. Banana Plugs – When connecting your speakers to the amplifier v300 banana jacks; Be sure that the red and black caps on the binding post are completely screwed in. Power Switch – This switch controls the units main power.

V Power Amplifier by American Audio Valuation Report by

If the input gain level is not reduced the built-in limiter will activate. Fuse Holder – 10 5 11 6 12 1 Diagram 3 This holder houses the external fuse.

Bridged-Mono Mode Caution – The voltage across the output terminals of a bridged V Vplus series amplifier may equal or exceed volts RMS and may be as high as volts.


The XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground. Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response.

Channel 1 subwoof frequency adj. The amplifier can operate at practically any power level without risk of overheating. It’s a community-based project which helps to repair anything.

Specifications rated output power,8 ohms Cooling System: Connecting to the wrong voltage is dangerous and may damage the amplifier. Configuring the Low Cut Filter: Inputs 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc.

The Output Short Circuit Protection protects the output devices of aurio amplifier from short circuits and stressful loads. To print the manual completely, please, download it.

This manual also for: To reduce the risk of electrical shock, do not remove cover. When the channel goes into protect mode all output for that channel will turn off. A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself. If this line good, check the internal speaker connections and components.

Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.